[Apr-2024] Exam Sure Pass Cisco Certification with 300-410 exam questions
Real Cisco 300-410 Exam Questions Study Guide
Career Prospects
The professionals who obtain the CCNP Enterprise certification can explore a wide range of highly rewarding careers. Some of the job roles that they can take up include a Cybersecurity Sales Specialist, an Enterprise Account Executive, a Network Architect, a Senior Software Engineer, a Healthcare Networking Specialist, a Network Security Application Engineer, a Cisco Network Security Engineer, and a Cloud Infrastructure Implementation Engineer, among others. With any of these positions, the applicants can expect to earn an average of $95,000 per year. Some of them can get as much as $120,000 or more per annum. This amount will depend on their job title, working experience, and related tasks.
What You Need to Know to Get the Cisco Certification
To get the CCENT certification, you will need to understand the fundamentals of routing and switching like IP addressing. You also need to make sure that your network device configurations are at the appropriate level for a small office network. Concentration is also needed on the skills of network security. Provider of CCENT exam certification is Cisco. The CCENT exam also includes questions about the LAN and WAN technologies that students need to know to succeed in their job. Major topics covered by Cisco CCENT certification are LAN switching, WAN switching, IPv4 addressing, IPv6 addressing, subnetting, routers and the fundamental concepts of the OSI model. Cisco 300-410 exam dumps are prepared by highly experienced IT experts. They make sure that all questions are up-to-date and accurate. Space of CCENT exam is very limited. Students have to go through the questions in a limited time duration. Thus, they need to know the right answers as well as time management skills.
Team of IT experts has been working since long time on the Cisco CCENT questions and answers. Space of CCENT exam is very limited. Time management skills are highly appreciated. Remember the time duration for answering of each question. A lot of Cisco CCENT exam questions are very hard to understand. Guide for Cisco CCENT exam is available for you. Sites for preparation of CCENT exam are numerous. Step by step CCENT exam preparation guide is available for you.
NEW QUESTION # 198
Refer to the exhibit. The output of the trace route from R5 shows a loop in the network. Which configuration prevents this loop?
- A.
- B.
- C.
- D.
Answer: B
Explanation:
Section: Layer 3 Technologies
NEW QUESTION # 199
Drag and drop the MPLS VPN concepts from the left onto the correct descriptions on the right.
Answer:
Explanation:
Reference:
https://www.rogerperkin.co.uk/featured/route-distinguisher-vs-route-target/
NEW QUESTION # 200 
Refer to the exhibit. An engineer is monitoring reachability of the configured default routes to ISP1 and ISP2.
The default route from ISP1 is preferred if available.
How is this issue resolved?
- A. Start IP SLA by matching numbers for track and ip sla commands.
- B. Use the icmp-echo command to track both default routes.
- C. Start IP SLA by defining frequency and scheduling it.
- D. Use the same AD for both default routes.
Answer: C
Explanation:
Section: Mixed Questions
NEW QUESTION # 201
Refer to Exhibit.
Traffic from the branch network should route through HQ R1 unless the path is unavailable. An engineer tests this functionality by shutting down interface on the BRANCH router toward HQ_R1 router but 192.168.20.0/24 is no longer reachable from the branch router. Which set of configurations resolves the issue?
- A. HQ_R1(config)# ip sla responder
HQ_R1(config)# ip sla responder icmp-echo 172.16.35.2 - B. BRANCH(config)# ip sla 1
BRANCH(config-ip-sla)# icmp-echo 172.16.35.1 - C. HQ_R2(config)# ip sla responder
HQ_R2(config)# ip sla responder icmp-echo 172.16.35.5 - D. BRANCH(config)# ip sla 1
BRANCH(config-ip-sla)# icmp-echo 172.16.35.2
Answer: D
Explanation:
In the configuration above, the engineer has made a mistake as he was tracking 172.16.35.6 (the backup path) instead of tracking the main path (172.16.35.2). Therefore,when he shut down the main path, the track 1 was still up so traffic still went through the main path -> it failed.
To fix this issue, we just need to correct the tracking interface of the main path.
NEW QUESTION # 202
Refer to the exhibit.
While troubleshooting an EIGRP neighbor adjacency problem, the network engineer notices that the interface connected to the neighboring router is not participating in the EIGRP process. Which action resolves the issues?
- A. Configure the network command under EIGRP address family vrf CLIENT1
- B. Configure the network command under EIGRP address family ipv4
- C. Configure EIGRP metrics on interface FastEthernet0/3
- D. Configure the network command to network 172.16.0.1 0.0.0.0
Answer: A
Explanation:
Explanation
router eigrp 1
!
address-family ipv4 vrf CLIENT1
network 172.16.0.0 0.0.0.255
no auto-summary
autonomous-system 1
exit-address-family
NEW QUESTION # 203
Refer to the exhibit.
Refer to the exhibit. Which action limits the access to R2 from 192.168.12.1?
- A. Modify sequence 20 to permit tcp host 192.168.12.1 eq 22 any to access-list 100
- B. Swap sequence 20 with sequence 10 in access-list 100
- C. Modify sequence 10 to deny tcp any eq 22 any to access-list 100.
- D. Swap sequence 10 with sequence 20 in access-list 100.
Answer: B
NEW QUESTION # 204
question: 140 Refer to the exhibits.
A user on the 192.168.1.0/24 network can successfully ping 192.168.3.1, but the administrator cannot ping
192.168.3.1 from the LA router. Which set of configurations fixes the issue?
A)
B)
C)
D)
- A. Option C
- B. Option A
- C. Option D
- D. Option B
Answer: D
NEW QUESTION # 205
An engineer needs dynamic routing between two routers and is unable to establish OSPF adjacency. The output of the show ip ospf neighbor command shows that the neighbor state is EXSTART/EXCHANGE.
Which action should be taken to resolve this issue?
- A. match the MTUs
- B. match the hello timers
- C. match the network types
- D. match the passwords
Answer: A
Explanation:
NEW QUESTION # 206
Which three protocols or protocol combinations does Management Plane Protection (MPP) support? (Choose three.)
- A. SSH
- B. OSPF
- C. Both HTTP and HTTPS
- D. FTP
- E. SFTP
- F. Only HTTP
Answer: A,C,D
Explanation:
Currently, MPP controls only the incoming management requests for protocols, such as TFTP, Telnet, Simple Network Management Protocol (SNMP), Secure Shell (SSH), and HTTP.
Following are the management protocols that the MPP feature supports. These management protocols are also the only protocols affected when MPP is enabled.
Blocks Extensible Exchange Protocol (BEEP)
FTP
HTTP
HTTPS
SSH, v1 and v2
SNMP, all versions
Telnet
TFTP
Reference: https://www.cisco.com/c/en/us/td/docs/ios/security/configuration/guide/sec_mgmt_plane_prot.html
NEW QUESTION # 207 
Refer to the exhibit. The R1 and R2 configurations are:
The neighbor relationship is not coming up.
Which two sets of configurations bring the neighbors up? (Choose two.)
- A.
- B.
- C.
- D.
- E.
Answer: C,E
Explanation:
Section: Mixed Questions
NEW QUESTION # 208
An engineer configured VRF-Lite on a router for VRF blue and VRF red. OSPF must be enabled on each VRF to peer to a directly connected router in each VRF. Which configuration forms OSPF neighbors over the network 10.10.10.0/28 for VRF blue and 192.168.0.0/30 for VRF red?
- A. Option C
- B. Option B
- C. Option A
- D. Option D
Answer: C
NEW QUESTION # 209
Refer to the exhibit.
Refer to the exhibit A CoPP policy is implemented to allow specific control traffic, but the traffic is not matching as expected and is getting unexpected behavior of control traffic. Which action resolves the issue?
- A. Create a separate class map lor ICMP traffic.
- B. Use match-any instruction in class-map
- C. Create a separate class map against each ACL.
- D. Use default-class to match ICMP traffic
Answer: B
NEW QUESTION # 210
Refer to the exhibit.
The Internet traffic should always prefer Site-A ISP-1 if the link and BGP connection are up; otherwise, all Internet traffic should go to ISP-2 Redistribution is configured between BGP and OSPF routing protocols and it is not working as expected. What action resolves the issue?
- A. Set metric-type 1 at Site-A RTR1, and set metric-type 2 at Site-B RTR2
- B. Set OSPF cost 200 at Site: A RTR1 and set OSPF Cost 100 at Site-B RTR2
- C. Set metric-type 2 at Site-A RTR1, and set metric-type 1 at Site-B RTR2
- D. Set OSPF cost 100 at Site-A RTR1, and set OSPF Cost 200 at Site-B RTR2
Answer: A
NEW QUESTION # 211
Refer to the exhibit.
An IP SLA is configured to use the backup default route when the primary is down, but it is not working as desired. Which command fixes the issue?
- A. R1(config)# ip route 0.0.0.0.0.0.0.0.2.2.2.2 10 track 1
- B. R1(config)#ip sla track 1
- C. R1(config)# ip route 0.0.0.0.0.0.0.0.1.1.1.1 track 1
- D. R1(config)# ip route 0.0.0.0.0.0.0.0.2.2.2.2
Answer: C
Explanation:
Reference:
Note: By default Static Router AD value-1 hence ip route 0.0.0.0. 0.0.0.0. 1.1.1.1 track 1 means AD-1 which must be less than of back up route AD.
Define the backup route to use when the tracked object is unavailable. !--- The administrative distance of the backup route must be greater than !--- the administrative distance of the tracked route. !--- If the primary gateway is unreachable, that route is removed !--- and the backup route is installed in the routing table !--- instead of the tracked route.
https://www.cisco.com/c/en/us/support/docs/ip/ip-routing/200785-ISP-Failover-with-default-routes-using-I.html
https://www.cisco.com/c/en/us/support/docs/security/asa-5500-x-series-next-generation-firewalls/118962-configure-asa-00.html
NEW QUESTION # 212
Refer to the exhibit.
An engineer is trying to block the route to 192.168.2.2 from the routing table by using the configuration that is shown. The route is still present in the routing table as an OSPF route. Which action blocks the route?
- A. Add this statement to the route map: route-map RM-OSPF-DL deny 20.
- B. Change sequence 10 in the route-map command from permit to deny.
- C. Use a prefix list instead of an access list in the route map.
- D. Use an extended access list instead of a standard access list.
Answer: B
NEW QUESTION # 213
Refer to the exhibit.
The administrator successfully logs into R1 but cannot access privileged mode commands. What should be configured to resolve the issue?
- A. enable secret or enable password commands to enter into privileged mode
- B. aaa authorization reverse-access
- C. secret cisco123! at the end of the username command instead of password cisco123!
- D. matching password on vty lines as cisco123!
Answer: A
NEW QUESTION # 214
Which feature drops packets if the source address is not found in the snooping table?
- A. IPv6 Source Guard
- B. IPv6 Prefix Guard
- C. IPv6 Destination Guard
- D. Binding Table Recovery
Answer: A
NEW QUESTION # 215
Refer to the exhibit.
R1 is connected with R2 via GigabitEthernet0/0, and R2 cannot ping R1. What action will fix the issue?
- A. Correct the IP SLA probe that failed.
- B. Fix IP Event Dampening configured on the interface.
- C. Replace the SFP module because it is not supported.
- D. Fix route dampening configured on the router.
Answer: B
Explanation:
NEW QUESTION # 216
Refer to the exhibit.
An engineer must redistribute networks 192.168.10.0/24 and 192.168.20.0/24 into OSPF from EIGRP. where the metric must be added when traversing through multiple hops to start an external route of 20 The engineer notices that the external metric is fixed and does not add at each hop. Which configuration resolves the issue?
- A. Option C
- B. Option A
- C. Option D
- D. Option B
Answer: D
NEW QUESTION # 217 
Refer to the exhibit. An engineer noticed that the router log messages do not have any information about when the event occurred. Which action should the engineer take when enabling service time stamps to improve the logging functionality at a granular level?
- A. Configure the timezone option
- B. Configure the msec option
- C. Configure the debug uptime option
- D. Configure the tog uptime option
Answer: D
NEW QUESTION # 218
Refer to the exhibit.
Which routes from OSPF process 5 are redistributed into EIGRP?
- A. only E1 subnets matching prefix listTO-OS1
- B. E1 and E2 subnets matching access list TO-OSPF
- C. only E2 subnets matching access list TO-OSPF
- D. E1 and E2 subnets matching prefix list TO-OSPF
Answer: B
NEW QUESTION # 219
Drag and drop the MPLS VPN concepts from the left onto the correct descriptions on the right.
Answer:
Explanation:
Reference:
https://www.rogerperkin.co.uk/featured/route-distinguisher-vs-route-target/
NEW QUESTION # 220
Refer to the exhibit.
Packets arriving from source 209.165.200.215 must be sent with the precedence bit set to 1, and packets arriving from source 209.165.200.216 must be sent with the precedence bit set to 5. Which action resolves the issue?
- A. set ip precedence priority in route-map Texas permit 20
- B. set ip precedence immediate in route-map Texas permit 10
- C. set ip precedence critical in route-map Texas permit 20
- D. set ip precedence critical in route-map Texas permit 10
Answer: C
NEW QUESTION # 221 
A network administrator is trying to access a branch router using TACACS+ username and password credentials, but the administrator cannot log in to the router because the WAN connectivity is down. The branch router has following AAA configuration:
Which command will resolve this problem when WAN connectivity is down?
- A. aaa authentication login default group tacacs+ enable
- B. aaa authentication login console group tacacs+ enable
- C. aaa authentication login default group tacacs+ local
- D. aaa authentication login default group tacacs+ console
Answer: C
NEW QUESTION # 222
Refer to the exhibit.
A network administrator logs into the router using TACACS+ username and password credentials, but the administrator cannot run any privileged commands Which action resolves the issue?
- A. Configure TACACS+ synchronization with the Active Directory admin group
- B. Configure an authorized IP address for this user to access this router
- C. Configure the username from a local database
- D. Configure full access for the username from TACACS+ server
Answer: D
NEW QUESTION # 223
......
Cisco 300-410 exam is a challenging test that covers a wide range of topics, including advanced routing protocols, VPN technologies, BGP, OSPF, and EIGRP. It also evaluates a candidate's knowledge of network services such as NAT, QoS, and multicast. Additionally, the exam assesses a candidate's ability to implement security features such as AAA, IPSec, and VPN. To succeed in the certification, candidates must have a deep understanding of networking concepts, protocols, and technologies, as well as practical experience in configuring and managing enterprise networks.
Updated and Accurate 300-410 Questions for passing the exam Quickly: https://www.itpassleader.com/Cisco/300-410-dumps-pass-exam.html
Download Real 300-410 Exam Dumps for candidates. 100% Free Dump Files: https://drive.google.com/open?id=1qBJGKYvQA9QvjYSI_-ySc3rtdFjvDJaJ