New 2021 Guaranteed Success with ITPassLeader 300-815 Dumps Cisco PDF Questions
Exceptional Practice To Implementing Cisco Advanced Call Control and Mobility Services Pass the First Time
Target Audience and Prerequisites
Every Cisco certification path can be taken by the individuals with any level of technical background, and this option is not an exception. This means that you can go for the Cisco 300-815 test right away if you want to. However, it is important to understand that this is a professional-level exam, so it will be much easier for you if you have some prior experience. The applicants for this test are recommended to possess from 3 to 5 years of experience to get started with the certification process. They are advised to have a general understanding of networking, video, and voice technologies, know how to describe various codecs as well as transform analogue voice into digital streams, be familiar with the Cisco IOS XE command line, possess the relevant skills in configuring and modifying the requirements within Cisco Unified CM, and so on.
The most important task for you to perform before going for the Cisco 300-815 exam is to pass the Cisco 350-801 test first. This is the core exam, which will help you understand the basics of the domain you are planning to enter. And then you can proceed with preparation for the concentration test. Also, please note that if you don’t want to obtain the CCNP Collaboration certificate, you can simply clear Cisco 300-815 and get the specialist-level certification.
Topics of Cisco 300-815: Implementing Cisco Advanced Call Control and Mobility Services Exam
In the 300-815 dumps, the following are also available:
1.0 Signaling and Media Protocols
- 1.2 Troubleshoot these H.323 protocol elements
- 1.1 Troubleshoot these elements of a SIP conversation
- 1.1.d Session timers
- 1.2.a DTMF
- 1.1.a Early media
- 1.1.c Mid-call signaling (hold/resume, call transfer, conferencing)
- 1.1.e UPDATE
- 1.1.b PRACK
- 1.3 Troubleshoot media establishment
- 1.2.b Call set up and tear down
2.0 CME/SRST Gateway Technologies
- 2.4 Configure these advanced Cisco Unified CME features
- 2.2 Configure Cisco Unified CME dial plans
- 2.4.c Paging
- 2.4.a Hunt groups
- 2.1 Configure Cisco Unified Communications Manager Express for SIP phone registration
- 2.3 Implement toll fraud prevention
- 2.4.b Call park
- 2.5 Configure SIP SRST gateway
3.0 Cisco Unified Border Element
- 3.1.e Header and SDP manipulation with SIP profiles
- 3.2.f Signaling and media bindings
- 3.1.f Signaling and media bindings
- 3.1.b Voice translation rules and profiles
- 3.1 Configure these Cisco Unified Border Element dial plan elements
- 3.2.a DTMF
- 3.2.b Voice translation rules and profiles
- 3.1.d Dial peers
- 3.2.d Dial peers
- 3.2.e Header and SDP manipulation with SIP profiles
- 3.1.a DTMF
- 3.2 Troubleshoot these Cisco Unified Border Element dial plan elements
- 3.2.c Codec preference list
4.0 Call Control and Dial Planning
- 4.1.g SIP trunking
- 4.2.c SIP route patterns
- 4.2 Troubleshoot these globalized call routing elements in Cisco Unified Communications Manager
- 4.1.c SIP route patterns
- 4.2.a Translation patterns
- 4.1.f TEHO
- 4.1 Configure these globalized call routing elements in Cisco Unified Communications Manager
- 4.1.d Transformation patterns
- 4.1.a Translation patterns
- 4.1.e Standard local route group
- 4.2.g SIP trunking
- 4.2.b Route patterns
- 4.2.d Transformation patterns
- 4.2.f TEHO
- 4.2.e Standard local route group
- 4.1.b Route patterns
5.0 Cisco Unified CM Call Control Features
- 5.6.c Call pick-up
- 5.6.a Call park
- 5.1 Troubleshoot Call Admission Control (exclude RSVP)
- 5.6 Configure supplementary functions
- 5.2 Configure ILS, URI synchronization, and GDPR
- 5.4 Configure call queuing
- 5.6.b Meet-me
- 5.5 Configure time of day routing
- 5.3 Configure hunt groups
6.0 Mobility
- 6.1 Configure Cisco Unified Communications Manager Mobility
- 6.2.b Extension Mobility
- 6.2 Troubleshoot Cisco Unified Communications Manager Mobility
- 6.1.b Extension Mobility 2019 Cisco Systems, Inc. This document is Cisco Public. Page 3
- 6.2.a Unified Mobility
- 6.2.c Device Mobility
- 6.1.a Unified Mobility
- 6.1.c Device Mobility
NEW QUESTION 68
Refer to the exhibit.
An engineer configures Cisco Unified Border Element to connect the enterprise VoIP network with a SIP telephony provider. Calls are not working in either direction. What must be configured in the dial peer 1 to fix the issue?
- A. answer-address 555 ........
- B. incoming called number 555.......
- C. session-protocol sipv2
- D. codec g729
Answer: C
NEW QUESTION 69
What is the relationship between partition, time schedule, and time period in Time-of-Day routing in Cisco Unified Communications Manager?
- A. A partition can have multiple time schedules assigned. A time schedule contains one or more time periods.
- B. A partition can have one time schedule assigned. A time schedule contains one or more time periods.
- C. A partition can have one time schedule assigned. A time schedule contains only one time period.
- D. A partition can have multiple time schedules assigned. A time schedule contains only one time period.
Answer: A
NEW QUESTION 70
An administrator configured Cisco Unified Mobility to block access to remote destinations for certain caller IDs. A user reports that a blocked caller was able to reach a remote destination. Which action resolves the issue?
- A. Configure a mobility identity.
- B. Configure Mobile Voice Access.
- C. Configure Single Number Reach.
- D. Configure an access list.
Answer: D
NEW QUESTION 71
Which two types of authentication are supported for the configuration of Intercluster Lookup Service? (Choose two.)
- A. username and secret key
- B. TLS certificates
- C. TokenID
- D. FQDN of the servers defined in DNS
- E. passwords
Answer: B,E
NEW QUESTION 72
A new deployment is using MVA for a specific user on the sales team, but the user is having issues when dialing DTMF. Which DTMF method must be configured in resolve the issue?
- A. gateway
- B. out-of-band
- C. in-band
- D. channel
Answer: B
NEW QUESTION 73
ABC company has decided to implement hunt groups to help distribute calls between members. In order to implement this, administrator must configure hunt list, hunt group, and line groups on Cisco UCM. Which distribution algorithms should the administrator implement?
- A. Top Down, Circular, Broadcast
- B. Top Down, Round Robin, Distribute
- C. Top Down, Round Robin, Broadcast
- D. Sequantial, Circular, Broadcast
Answer: A
NEW QUESTION 74
Why would RTP traffic that is sent from the originating endpoint fail to be received on the far endpoint?
- A. Cisco Unified Communications Manager invoked media termination point resources.
- B. A firewall in the media path is blocking TCP ports 16384-32768.
- C. The RTP traffic is arriving beyond the jitter buffer on the receiving end.
- D. The far end connection data (c=) in the SDP was overwritten by deep packet inspection in the call signaling path.
Answer: B
Explanation:
Section: Signaling and Media Protocols
NEW QUESTION 75
Refer to the exhibit.
Which change to the translation rule is needed to strip only the leading 9 from the digit string 9123548?
- A. rulel /.*\(3548S\)/^1/
- B. rule 1 /^9\(.*\)/A1/
- C. rulel /^9\(\d*\)/^1/
- D. rule 1/^9123548/^1/
Answer: B
NEW QUESTION 76
A company has users that are logged in to hunt groups. However, there is a requirement for hunt group configurations to provide an option to turn on audible ringtones when calls to a line group arrive at a phone that is logged out and on a break. This ringtone alerts a logged-out user that there is an incoming call to a hunt list to which the line is a member, but the call does not ring at the phone of that line group member because of the logged-out status. Which action meets this requirement?
- A. Configure the HLog softkey on the phone so that while a user is logged off, it plays an audible tone when a call is missed.
- B. Configure the service parameter hunt group logoff notification and specify the name of the ringtone file.
- C. Set the service parameter Enterprise Feature Access number for hunt group logout and set up an access number
- D. Set the service parameter Party Entrance Tone to True."
Answer: B
NEW QUESTION 77
An engineer is troubleshooting local ringback on a Cisco SIP gateway The gateway is not ignoring the SIP 180 response with SDP from the service provider, and the far end device is sending the 180 with SDP to play ringback from the IP address specified m the SDP Which configuration change must be made on the gateway to resolve the issue?
- A. Router(config-sip-ua)# no disable-early-media 180
- B. Router(con(-voi-serv)# no disable-early-media 180
- C. Router(conf-voi-serv)# dlisable-early-media 180
- D. Router(conftg-sip-ua)# disable-early-media 180
Answer: D
NEW QUESTION 78
Refer to the exhibit.
Users report that outbound PSTN calls from phones registered to Cisco Unified Communications Manager are not completing. The local service provider in North America has a requirement to receive calls in 10-digit format. The Cisco Unified CM sends the calls to the Cisco Unified Border Element router in a globalized E.164 format. There is an outbound dial peer on Cisco Unified Border Element configured to send the calls to the provider. The dial peer has a voice translation profile applied in the correct direction but an incorrect voice translation rule applied, which is shown in the exhibit. Which rule modified DNIS in the format that the provider is expecting?
- A. rule 1 /^\+1\([2-9]..[2-9]......$\)/ /\0/
- B. rule 1/^\+1\([2-9]..[2-9]......$\)/ /\1/
- C. rule 1 /^\([2-9]..[2-9]......$\)/ /\1/
- D. rule 1 /^/+\([^1].*\)/ /011\1/
Answer: B
NEW QUESTION 79 
Refer to the exhibit. How many maximum hops can an ILS updarte traverse?
- A. 0
- B. 1
- C. 2
- D. 3
Answer: A
Explanation:
Section: Cisco Unified CM Call Control Features
NEW QUESTION 80
You see the voice register pool 1 command in your Cisco Unified Communications Manager Express configuration. Which configuration is occurring in this section?
- A. configuration for a pool of SIP phones (similar to device pool on Cisco Unified Communications Manager)
- B. configuration for a single SIP phone
- C. configuration items common for all SIP phones
- D. configuration for SIP registrar service
Answer: A
Explanation:
Reference:
https://www.cisco.com/c/en/us/td/docs/voice_ip_comm/cusrst/admin/sccp_sip_srst/configuration/ guide/SCCP_and_SIP_SRST_Admin_Guide/srst_setting_up_using_sip.html
NEW QUESTION 81
Which call pickup feature allows users to pick up incoming calls in a group that is associated with their own group?
- A. Directed Call Pickup
- B. Other Group Pickup
- C. Group Call Pickup
- D. BLF Call Pickup
Answer: B
Explanation:
Reference:
https://www.cisco.com/en/US/docs/voice_ip_comm/cucm/admin/4_1_3/ccmsys/ a07cpick.html#wp1022865
NEW QUESTION 82
An engineer set up and successfully tested a TEHO solution on the Cisco UCM. PSTN calls are routed correctly using the IP WAN as close to the final PSTN destination as possible. However, suddenly, calls start using the backup local gateway instead. What is causing the issue?
- A. WAN connectivity
- B. route pattern
- C. LAN connectivity
- D. route list and route group
Answer: A
NEW QUESTION 83
What are two configureation features of the Client matter code setting in the route pattern configuration? (Choose two.)
- A. Selecting the Allow Overlap Sending setting allows a user to select the Require Client Matter Code setting.
- B. Selecting the Allow Overlap Sending setting disables the Require Client Matter Code setting.
- C. The Client Matter Code feature provides the option to configure Authorization Level susch as in the Forced Authorization Code.
- D. The client Matter Code feature supports overlap sending since the Cisco UCM can determine when to prompt the user for the code.
Answer: B,C
NEW QUESTION 84
Refer to the exhibit.
Within the North American Numbering Plan, gateways located in Ottawa, Canada and marked as "YOW" are assigned to the Calling Party Transformation CSS NANP_CgPTP, which contains partition NANP_calling_xforms. What is the calling-party number and the numbering type if the calling user +1613-555-1234 dials the number?
- A. calling number 613-555-1234 and numbering type "national"
- B. calling number 011613-555-1234 and numbering type "international"
- C. calling number 011-1-613-555-1234 and numbering type "subscriber"
- D. calling number 613-555-1234 and numbering type "subscriber"
Answer: A
NEW QUESTION 85
When you troubleshoot H.323 call setup, which message informs you that the called party is being notified about the call?
- A. CONNECT
- B. RINGING
- C. ALERTING
- D. PROCEEDING
Answer: A
Explanation:
Section: Signaling and Media Protocols
NEW QUESTION 86
Refer to the exhibit.
DN 1003 was the last to ring during the most recent call. Which hunting method ensures that DN 1005 is presented with the next call when the hunt pilot is dialed?
- A. parallel
- B. peer
- C. call-blast
- D. sequential
Answer: B
NEW QUESTION 87
Refer to the exhibit.
DN 1003 was the last to ring during the most recent call. Which hunting method ensures that DN 1005 is presented with the next call when the hunt pilot is dialed?
- A. parallel
- B. peer
- C. call-blast
- D. sequential
Answer: B
NEW QUESTION 88
The administrator of ABC company is troubleshooting a one-way audio issue for a call that uses H.323 protocol (slow-start mode). The administrator requests that you provide the IP and port information of the Real- Time Transport Protocol traffic that had the one-way audio call.
You gather the H.225 and H.245 messages for one of the one-way audio calls. Where can you find the RTP IP and port information for both sides? (Note: This call flow has not invoked any media resources like MTP or transcoders).
- A. H.245 Open Logical Channel
- B. H.245 Terminal Capability Set
- C. H.245 Open Logical Channel Ack
- D. H.225 Connect
Answer: A
Explanation:
Reference:
http://ccievoicehopeful.blogspot.com/2012/09/h323-notes.html
NEW QUESTION 89
Where on Cisco Unified Communications Manager do you configure the standard local route group for a group of devices?
- A. System > Device Pool
- B. Call Routing > Emergency Location > Emergency Location (ELIN) Groups
- C. Call Routing > Route/Hunt > Local Route Group Names
- D. System > Location Info
Answer: C
Explanation:
Reference:
https://www.uccollabing.com/configuring-standard-local-route-group-cucm/
NEW QUESTION 90
......
300-815 EXAM DUMPS WITH GUARANTEED SUCCESS: https://www.itpassleader.com/Cisco/300-815-dumps-pass-exam.html
Best Quality Cisco 300-815 Exam Questions: https://drive.google.com/open?id=1Vv4hWil9QJJAbBVVcW9xOc_OMmOfKUNe